Concrete Solution Center
Calculate material, account for waste, and build the complete job before concrete arrives.
Enterprise Concrete Takeoff Center™
Use practical field calculators to establish the requirement, add the right allowance, and turn the result into an actionable material conversation.
Step 01 — Choose the work
Pick the closest shape. We will ask only the questions that change the takeoff.
Slab Takeoff
Concrete, base, forms, vapor protection, reinforcement supports, joint layout, early-entry cutting, cure, and sealing will share the same dimensions.
Wall Takeoff
Calculate concrete, contact area, handset-form planning quantities, reinforcement, ties, release, bracing, and placement accessories.
Round / Cylinder Takeoff
Use diameter in inches and depth in feet/inches. The plan adds concrete, form tube, reinforcing cage, bracing, embeds, and curing accessories.
Complete Working Takeoff
Concrete Workflow Intelligence™
Choose the stage. Supply Haus will organize the products, equipment, documentation, and human support around the work in front of you.
Stage 01 — Plan & Estimate
Confirm quantities, allowances, conditions, and the system required to execute the pour.
Recommended System
Project specifications and field conditions govern final product selection.
Stage 02 — Prepare & Form
Prepare the base, establish the edge, control moisture, and build formwork ready for placement pressure.
Recommended System
Project specifications and field conditions govern final product selection.
Stage 03 — Reinforce
Build the reinforcing system, maintain cover, and keep steel where the design requires it.
Recommended System
Project specifications and field conditions govern final product selection.
Stage 04 — Place
Move, consolidate, strike, and control fresh concrete without losing the schedule or the crew.
Recommended System
Project specifications and field conditions govern final product selection.
Stage 05 — Finish
Manage the surface from initial strike-off through final texture with tools matched to the finish.
Recommended System
Project specifications and field conditions govern final product selection.
Stage 06 — Cure & Protect
Control moisture loss, protect early strength, and deliver the performance the mix was designed to achieve.
Recommended System
Project specifications and field conditions govern final product selection.
Stage 07 — Repair & Maintain
Diagnose the failure, prepare the substrate, and select a compatible repair system for lasting performance.
Recommended System
Project specifications and field conditions govern final product selection.
Concrete Concierge
Bring us the pour, the problem, or the plans. A Supply Haus concrete human will help assemble the complete system.
Concrete Solution Center™ / Project Intelligence
Enter the job once. The Concrete Project Planner™ connects volume, base, forming, reinforcement, curing, jointing, and the minimum material recipe—then sends the complete plan to a real Supply Haus human.
Project Intelligence / HEF-805
Calculated quantities, planning estimates, open decisions, and one complete Concierge request.
Step 01 / Project Recipe
Select the closest project. We will ask only the questions that affect that work.
Step 02 / Shared Job Profile
These measurements feed every calculation that applies to the selected work.
We will never silently assume whether the pool is included in your stated dimensions.
This answer changes which measurements, calculations, and material groups apply.
Aggregate base is calculated only when full-depth work actually includes base replacement.
Pool / Opening
Curves, radii, coping, steps, equipment pads, islands, and irregular geometry require manual takeoff review.
Step 03 / Execution Choices
Unknown is an acceptable answer. The plan will preserve it for review instead of guessing.
Adaptive Slab Assembly
Subgrade and base feed vapor protection, reinforcement supports, reinforcement, and the concrete placement. Only applicable slab work opens this gate.
Chair height, concrete cover, support class, spacing, upper-mat support, corrosion protection, and compatibility with the vapor barrier must follow the plans and selected support-system data.
Adaptive Finish Gate
Coverage, application rate, compatible cure, sealer, tooling, timing, and maintenance requirements come from the selected manufacturer's current technical data. Decorative score lines do not replace required structural joints.
Drawing / Photo Intake
Upload a plan PDF, take a phone photo of a drawing, share a field sketch, or provide a secure link. Extracted values never override your entered dimensions without confirmation.
Project upload reference
HEF805 Use this same reference in the upload form so the file and project plan stay together.The planner request carries the upload reference, document metadata, and any secure link. The file itself must be submitted through the configured upload form; Shopify's native contact form does not attach files.
Step 04 / Concrete Project Plan™
Review calculated quantities, estimates, assumptions, and unresolved decisions before sending.
Milk / Bread / Eggs
Triggered by the work
Do not guess
Concrete Volume
—Waiting for dimensionsAggregate Base
—Compacted planning volume; loose conversion requires material confirmation.Reinforcement
—Coverage basis only; design, laps, supports and spacing follow plans.Cure & Sealer
—Surface area basis; product coverage and compatibility govern containers.Edge Forming
—Preliminary perimeter; stakes, kickers, corners and reuse are field-dependent.Sawcut Plan
—Rectangular planning grid only.Joint Treatment
—Only designated joints receive sealant; joint-system details govern quantity.Bag Yield
—Uses nominal 0.60 ft³ per 80-lb bag; selected product data governs.Vapor System
—Roll and tape planning basis; selected system, seams, penetrations and terminations govern.Reinforcement Supports
—Preliminary chairs or bolster only; height, cover, spacing and support class follow plans.This is a preliminary material and execution plan—not an engineered design, approved mix, structural reinforcement schedule, drainage design, joint drawing, or product-compatibility determination. Plans, specifications, codes, manufacturers, engineers, inspectors, and field conditions govern.
Step 05 / Human Review
Your dimensions, quantities, recipe, assumptions, and unresolved questions will travel together.